ASTM D3487-00 FED SPEC# VV-I-530 | Xceltherm® Electrical Insulating Oil, Type I

Radco Industries, Inc.	Qualification Number: Not Applicable
PO Box 305	Qualification Date: Not Applicable
LaFox, IL 60147	Manufacturing Location: LaFox IL 60147
Telephone: (800) 854-4865	Fax: (630) 232-7968

Properties

Test Method

Limit

Typical Result

Physical:

Aniline Point °C

ASTM-D611

63-84

70.4

Color

ASTM-1500

0.5 max

<0.5

Flash Point, Minimum °C

ASTM-D92

146

154

Interfacial Tension (@25°C) MIN

ASTM-D971

40 dynes/cm

50 dynes/cm

Pour Point °C Maximum

ASTM-D97

-40°C

-61°C

Specific Gravity, 15/15°C, Max

ASTM-D1298

0.91

0.8850

Viscosity, max, cSt (SUS) at:

100°C	ASTM-D455	3.0 max	2.3
40°C	ASTM-D455	11.0 max	9.6
0°C	ASTM-D455	76.0 max	67

Visual Examination

ASTM-D1524

Clear and Bright

PASS

Electrical:

Dielectric Breakdown Voltage @ 60 HZ:

Disk Electrodes, min kV	ASTM-D877	30	47
VDE Electrodes, min, kV 0.040-in (1.02-mm) gap	ASTM-D1816	28	42
0.080-in (2.03-mm) gap	ASTM-D1816	56	63

Dielectric breakdown voltage,
impulse, conditions,
@ 25°C, needle-to-sphere
grounded, 1 inch (25.4mm) gap

ASTM-D3300

145 kV

274 kV

Gassing Tendency, max, uL/min

ASTM-D2300

+30

+12

Power Factor, 60 HZ

@ 25°C, %	ASTM-D924	0.05	0.009
@ 100°C, %	ASTM-D924	0.030	0.06

Chemical:

Oxidation Stability @ 72 hrs:

% sludge, max, by mass	ASTM-D2440	0.15 max	0.004
TAN, max, mg KOH/g	ASTM-D2440	0.5 max	0.02

Oxidation Stability @ 164 hrs:

% sludge, max, by mass	ASTM-D2440	0.3	0.03
TAN, max, mg KOH/g	ASTM-D2440	0.6	0.04

Oxidation Stability (RBOT), min

ASTM-D2112

---

243

Oxdation Inhibitor content, max, % by mass

ASTM-D2668

0.08

0.05

Corrosive Sulfur

ASTM-D1275

Non-corrosive

Water, max, ppm

ASTM-D1533

Neutralization No, TAN, mg KOH/g

ASTM-D974

0.03

<0.01

PCB Content, ppm

ASTM-D4059

Not Detectable

Xceltherm® Electrical Insulating Oil (Type I) meets military standard specifications for electrical oil applications. Xceltherm® EIO-I has high electrical resistance and is both thermally and oxidatively stable. Xceltherm® EIO-I is intended for use in most common electrical insulating oil applications where normal oxidation resistance is required. It is compatible with other electrical insulating oils, including Shell Diala® A.

Military Fluids ASTM D3487-00 FED SPEC# VV-I-530 XCELTHERM® ELECTRICAL INSULATING OIL, TYPE I

Military Fluids
ASTM D3487-00 FED SPEC# VV-I-530
XCELTHERM^® ELECTRICAL INSULATING OIL, TYPE I